A STEP-BY-STEP OVERVIEW TO INSTALLING A BATHTUB

A Step-by-Step Overview to Installing a Bathtub

A Step-by-Step Overview to Installing a Bathtub

Blog Article

Further Details

How do you feel on the subject of Tools You Need to Install a New Bathtub ?


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't specifically rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is easily accessible, the job can move immediately; if you have to open a wall surface to eliminate the old bathtub and place the brand-new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require an assistant to leave the old bathtub and embeded in the brand-new one. Ensure you have actually certified yourself for the work and also are comfortable attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your restroom if you have actually currently bought a new bathtub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and material checklist ought to make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic due to the restricted accessibility that is usually the case.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
    Prior to proceeding to fit the new faucets, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Fitting New Taps


    If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipes.
    If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, place the tap in the installing opening in the bath/basin making sure that the washers are in area in between the tap as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous type should be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

    Installing the Tub


    Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are valuable in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four tiny factors.
    The following objective is to make sure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bathtub until the spirit level reads level.
    To install taps, fit the bottom of the furthest flexible tap adapter to the proper supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
    Switch on the water supply and check all joints as well as new pipework for leaks and also tighten them if necessary. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
    Finally, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and also securing around the bath tub needs to wait up until the bathtub has actually been made use of at the very least when as this will certainly settle it into its final position.

    Preparing for the Installation


    Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the faucets system to avoid strain on the bath tub.
    Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be fitted in its last setting.

    Tiling Around the Bath tub


    In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling below.
    You can select from a selection of coloured sealants to blend in your components and also fittings. They are offered in tubes and also cartridges, and also are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the tub remains in usage. The sealer can fracture fairly early if you do not take into consideration this motion prior to securing.
    Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof glue and also cement.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub

    I stumbled upon that blog entry on A Step-by-Step Guide to Installing a Bathtub when browsing the web. Appreciated our review? Please share it. Let somebody else find it. We cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.




    Get Your Estimate Now


    Report this page